Heater & Furnace Repair in Mabank & DFW

When a Texas cold front rolls in and your heat dies, you have hours — not days — before pipes freeze and a comfort problem becomes a property-damage emergency. We dispatch same-day for heater and furnace repair across Mabank, Cedar Creek Lake Area, and the DFW metro. Gas furnaces, electric heat strips, heat pumps — we work on every brand and every system type.

Common Heating Problems We Fix

Heating failures in Texas tend to fall into recognizable patterns — most often during the first hard cold snap when systems wake up after months of disuse:

• Furnace won't ignite — failed igniter, dirty flame sensor, blocked condensate trap, or pilot/thermocouple issue
• Heater blowing cold air — overheating limit switch tripped, clogged filter, or failed gas valve
• Burner cycling on and off — dirty flame sensor, cracked heat exchanger (safety issue), or thermostat short cycling
• Heat pump running but not heating — failed reversing valve, low refrigerant, or stuck defrost cycle
• Weak airflow with system running — clogged filter, blower motor failing, or restricted ductwork
• Loud bang on startup — delayed ignition (potentially dangerous — turn off and call us)
• Smell of gas near furnace — leave the house, call the gas company first, then us

Our Heating Repair Process

• 1. Pre-call dispatch — text with tech name, photo, and ETA
• 2. Combustion safety check — CO test at every visit, no exceptions
• 3. Full diagnostic — gas pressure, ignition sequence, flame rectification, blower motor amp draw, heat exchanger inspection
• 4. Upfront written quote — flat-rate, signed off before any work begins
• 5. Repair — done same visit when possible
• 6. Post-repair verification — combustion analysis re-tested to confirm safe operation

Heating Repair Pricing

• Diagnostic / service call: $79 (waived if you book the repair)
• Igniter (hot surface) replacement: $220–$340
• Flame sensor cleaning / replacement: $140–$220
• Gas valve replacement: $420–$640
• Inducer motor replacement: $520–$780
• Blower motor replacement: $420–$780
• Control board replacement: $480–$720
• Heat exchanger replacement: $1,400–$2,800 (often replace-system-instead decision)
• Heat pump reversing valve: $680–$1,100

Cracked Heat Exchanger — When It's Time to Replace

A cracked heat exchanger is a serious safety issue — it can leak carbon monoxide into your home. We test for cracks at every heating diagnostic with a flue gas analyzer. If your system is over 12 years old and the heat exchanger is compromised, replacement of the whole furnace is almost always more economical than a heat exchanger swap. We'll show you the readings and give you the honest math.

Same-Day Heater & Furnace Repair — Mabank, Cedar Creek Lake & DFW

Searching "heater & furnace repair near me"? We dispatch same-day for most heater & furnace repair calls across our entire service area — Mabank, Gun Barrel City, Seven Points, Kemp, Tool, Athens, Kaufman, and the full Dallas–Fort Worth metroplex including Plano, Frisco, Allen, McKinney, Arlington, Mesquite, Garland, and Rockwall. A real human answers the line 24/7 — usually Eric, Brad, or a senior tech, never a call center. Whether you searched for "heater & furnace repair", "heater & furnair conditioninge repair", "HVAC contractor near me", or "best heating company [your city] TX", we cover it — veteran-owned, locally operated, never acquired by private equity.

Brand-Name HVAC Equipment We Service

We service every major HVAC brand on the market across our Mabank and DFW service area: Trane, Carrier, Lennox, Goodman, Rheem, Amana, York, Bryant, American Standard, Heil, Daikin, Mitsubishi. Whether your existing equipment is 5 years old or 20, whether it's a high-end inverter system or a builder-grade base model, we approach the work the same way — honest diagnostic, flat-rate written quote, repair or install done right the first time.

Don't see your equipment brand listed? Call anyway. The HVAC industry only has a handful of core compressor and heat-exchanger manufacturers behind the dozens of consumer-facing labels — if it's a residential or light-commercial system, we likely service it.

Frequently Asked Questions